TFI and Heritage bars on 09 Road King

Discussion in 'TFI Settings' started by bfmitch, May 13, 2009.

  1. bfmitch

    bfmitch Active Member

    133
    26
    1
    TFI and Stage 1
    Did my stage 1 last Friday. I already had Rush pipes with 2" baffles on the bike. I had bought a TFI and had it sitting on the shelf until I got my Screaming Eagle AC. Finally got the AC last Friday and got everything installed Friday afternoon.

    Installing the TFI is easy. Just follow the instructions. I used the settings in the instruction sheet. Set the Green pot to 2:30, the Yellow to 3:25, the Red to 3:15 and the RPM pot to 4:00. You have to look at the total width of the arrow on the pot and figure out the position you want. You'll get it after a couple minutes.

    The instructions don't tell you how to route the wiring from the TFI to the fuel injectors. (I had a professor who would say "that exercise is left for the student") I put my TFI in the empty spot behind the right side cover. I routed the wiring up along the frame member next to the tank. So far it looks to be staying there just fine.

    The AC is actually harder to install than the TFI, although anyone who can follow instructions can get it done. Put just a bit of grease on the O rings so they stay in the shoulder of the bolt. If you don't the O ring can move and it will get pinched in the wrong position. You can probably guess how I learned that.

    What a difference. The exhaust popping on deceleration is gone. As is the occasional loud backfire on startup when the engine was hot and had only been shut off for a few minutes. Just a nice loud burble when I back off the throttle. Acceleration is also much better. The RK wasn't bad to begin with but now it's in another class. It accelerates better and pulls longer in each gear. Two up the Road King can now, suprisingly, pull away from my son's '08 Super Glide Custom pretty smartly. That's when he is One up. Used to be I had to work to stay with him.

    I filled up my tank just before installing the stage 1 parts. I calculated that tank at 39.7 MPG. That was a mix of riding two up and by myself, mostly around town. After installing the stage 1 I rode Sunday and Monday. Pretty much the same kind of riding except I have to admit I got on it a bit. When I refilled I got 37.8 MPG. Not too shabby. If I can leave the throttle alone I might do better. But, where's the fun in that?

    The engine is running cooler too. The semi-scientific measurement I'm using is the heat on the back of my right leg and the fact that the rear cylinder didn't have to shut off when I was caught in traffic yesterday. I'll be changing to synthetic oil (Red Line) this weekend. It should be even better when that's done. I'm going to need every bit of cooling I can get when the temperature really starts to climb around here.

    The bike even sounds better now.


    Heritage Bars
    Today I installed the new Heritage bars made for the FLHR. The dealer quoted me $800 to install them. The bars were $79.95. (I could have saved 20% by ordering them but I'm sometimes a spur of the moment person for stuff like that.) I installed the bars myself in about 3 hours. That's with quite a few smoke and coffee breaks while I re-read the manual. I used a replacement factory left grip from the dealer for $6.95.

    Here's something to remember. I didn't see it in the manual. Remove the plastic cable ties that hold the wiring from the controls tight to the handlebars. If you don't, the wiring that runs through the bars will get hung up on them as they stick inside the handlebar. (three guesses how I learned that one.) I popped them out and the wiring slide through nice as can be. Buy 4 of them when you get the bars. They don't go back in as nicely after you pull them out.

    You can install the part of the harness that runs from the throttle control to the nacelle before you put the new bars on. I did that and didn't need any sort of wire to snake the harness through the handle bars. Gravity and the stiffness of the harness did the trick.

    Do be careful when disconnecting the wiring on the throttle control from the harness. If you break the little green locking tab there is no fix to it. At least that's what the manual says. I figure you could wrap the connector with electrical tape and it would hold together pretty well. I didn't make that mistake since I'm used to dealing with connectors like that.

    After a 20 mile ride I like the new bars but they do make the bike handle a bit differently. It leans into corners much faster now (I think because I'm sitting more upright) and is more sensitive on the nasty gravel road I have to drive on. I'll get used to that.

    Sorry for the long winded post. I figured some of you might want to hear about it.
     
  2. Timman

    Timman Member

    43
    16
    0
    I good read Burt, I been trying to read all I can about doing a stage one. I have a 09 Road King and put Heritage Bars on my bike also, I also am going to do the stage one, I got the Air Cleaner and am going to order a TFI unit but still can't deside what to get for pipes. thanks for the tips. Tim
     
  3. NEWHD74FAN

    NEWHD74FAN Experienced Member Retired Moderators

    8,176
    98
    16
    Burt, nice post and well documented. I bet you know what my next question will be...do you have a few pictures of your installation of the TFI and your bike?...Yea, it would be nice to see your work in all it's tuned glory! :s
     
  4. bfmitch

    bfmitch Active Member

    133
    26
    1
    Sorry, no pictures. I hadn't planned to write about it when I did it. If anyone who is planning to do this is within a couple hundred miles of Salt Lake City, I'd be happy to work with you and show you what I did.

    I've changed one thing since I did the initial installation of the TFI. The TFI unit is in the same spot I previously described but I dismounted the fuel tank and ran the injector wires through the wiring channel under the tank. I dropped them down out of the channel at the same place the factory injector wiring goes. Now I don't have to worry about the wiring melting on the valve covers. I really don't think it would have. I took one long trip with the wiring in it's initial position. I checked it a few times on that trip and the wiring was staying where I stuffed it. I just think the way I have it now is a better way to do it.

    I've been happy with the Rush pipes with the 2" baffles. When you decide on your pipes contact TFI and tell them exactly what you have (bike, engine, air cleaner and pipes) They gave me some new settings that were slightly different from the settings in the instructions. The bike runs even better now.
     
  5. FLHXTom29715

    FLHXTom29715 Active Member

    162
    16
    0
    Hey Burt, I too thank you for your write up.Just got an '09 SG and waiting for my rush pipes with 2" baffles, waiting on my SE heavy breather and now getting ready for fuel control, I had a TFI in my 98 RK and at that time you had to hook up inline with jumpers, I had it on my RK for a good 6 years with no problems. After reading your write up I was going to ask how has it been since May, it seems it's been good for you. Tom
     
  6. bfmitch

    bfmitch Active Member

    133
    26
    1
    I've had the TFI installed for about 8K miles. I like the performance improvement. You'd have to hold a gun to my head to get me to remove it.

    Around town I'm getting about 40 MPG. Cruising, two up, about 44 MPG. I haven't taken any long rides without my wife on the back. I expect I'll get even better mileage one up.

    I have absolutely no problem recommending it. When we complete the Stage 1 on my son's bike we'll use the TFI. My wife wants to get a Softail Deluxe next year. I'll use the TFI on that.
     
  7. sharpscuba

    sharpscuba Banned

    945
    0
    1
    I agree to all ..the TFI, Rush 2" pipes and I used the Big sucker A.C. I love the way the bike runs and the milage is a bit better. I did'nt notice much change in the heat but still happy.