You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
H-D Factory Security System Install
- Thread starter glider.
- Start date
can someone help before i have a breakdown!
yesterday i was on here and i managed to find a link to a file down load
which lead to the box.
it was a diagram of the hd alarm i have fitted. i now cannot find it anywhere, please help
Was it this?
Harley Davidson Community - HDTimeline Downloads Page - 2008 Security And Maintenance Catalog
or in this section?
Alarms and Security Related Issues - Harley Davidson Community
If you could be a bit more specific as to what you need, it would help.
Thanks for the help but i managed to find it.
ive downloaded it now. it was an actual diagram for the hd alarm.
i am trying to get a bike going.
can anyone help out. the bike is a flhtc
ive not fob and no pin. i know it sounds dodgy but it's not.
the dealer is miles away and i need to start the bike.
ive held the trip button in and managed to get a code of 82883
is this my pin code?
the signal indicatrors are missing at the moment cause they are being repaired.
the bike is almost ready to ride so i want to fire her up.
the model is a flhtc with a 1450cc
any help would be great.
as at the moment ive tried to put pin numbers 10 & 9
to ground. and live.
and still cant get it going !
ive downloaded it now. it was an actual diagram for the hd alarm.
i am trying to get a bike going.
can anyone help out. the bike is a flhtc
ive not fob and no pin. i know it sounds dodgy but it's not.
the dealer is miles away and i need to start the bike.
ive held the trip button in and managed to get a code of 82883
is this my pin code?
the signal indicatrors are missing at the moment cause they are being repaired.
the bike is almost ready to ride so i want to fire her up.
the model is a flhtc with a 1450cc
any help would be great.
as at the moment ive tried to put pin numbers 10 & 9
to ground. and live.
and still cant get it going !
The 82883 sounds like the typical 5 digit code that is used.
Where did you find the diagram for the alarm?
Post a link and maybe we can figure it out.
Take a look here for the PIN code setup.
Programming / Using Manual Security Code (both FOB's) - Harley Davidson Community
Where did you find the diagram for the alarm?
Post a link and maybe we can figure it out.
Take a look here for the PIN code setup.
Programming / Using Manual Security Code (both FOB's) - Harley Davidson Community
I don't remember where i found it in the end.
i was looking at them all.
ive downloaded it though so i don't have to look again.
it was just a link to the box place
where you can then download it.
the code above im told is the factory code used.
there was a load of stuff before that came up.
basically something and 1-10 clr .
ive found this out and it is the fault codes.
all clear then?
well why wont it take in the pin code?
and why does it give the pin code when i do not have a working remote?
the alarm does not sound even though the siren is also backed up with a 9volt.
im lost.
the wires ive mentioned above go to the starter relay and the other the ecu.
however the starter one ive grounded and it now cranks.
the other ive tried to ground and stuck it to a live.
the coil plug has 3 wires going to it. a large white and black striped
a red and blue and a yellow and black i think.
anyway the live is the white and black striped.
one of the others pulses neg rapidly when cranking.
is this right and what should the other do?
[URL="http://www.box.net/shared/6bzdi5vcw8[/URL]
i was looking at them all.
ive downloaded it though so i don't have to look again.
it was just a link to the box place
where you can then download it.
the code above im told is the factory code used.
there was a load of stuff before that came up.
basically something and 1-10 clr .
ive found this out and it is the fault codes.
all clear then?
well why wont it take in the pin code?
and why does it give the pin code when i do not have a working remote?
the alarm does not sound even though the siren is also backed up with a 9volt.
im lost.
the wires ive mentioned above go to the starter relay and the other the ecu.
however the starter one ive grounded and it now cranks.
the other ive tried to ground and stuck it to a live.
the coil plug has 3 wires going to it. a large white and black striped
a red and blue and a yellow and black i think.
anyway the live is the white and black striped.
one of the others pulses neg rapidly when cranking.
is this right and what should the other do?
[URL="http://www.box.net/shared/6bzdi5vcw8[/URL]
If you have the link to BOX.net., post that up here.
Meanwhile, I don't know if you saw this link above.
Programming / Using Manual Security Code (both FOB's) - Harley Davidson Community
Meanwhile, I don't know if you saw this link above.
Programming / Using Manual Security Code (both FOB's) - Harley Davidson Community
dschinella
Member
So does that mean I just can't purchase the new alarm system with fobs and intall it my self?
So does that mean I just can't purchase the new alarm system with fobs and intall it my self?
Yes you can but the dealer has to initialize the fobs for you then.
also trouble with encoding the pager. I have a road king custom 04 with smart siren 2 AND when i put the bike off, the alarm is set automaticlly after 30 seconds.
Tried to encode the pager with the orginally insctruction sheet but no suc 6. Have search many topics and trie so many things.. but nothing. Hopefully someone can help me!
Tried to encode the pager with the orginally insctruction sheet but no suc 6. Have search many topics and trie so many things.. but nothing. Hopefully someone can help me!