2007 XL883L jiffystand spring part number?

Discussion in 'Sportster Models' started by Steve_Benoit, Jun 5, 2009.

  1. Steve_Benoit

    Steve_Benoit Member

    27
    11
    0
    Hi Folks

    Could someone with a parts/service manual for a 2007 Sportser xl883L look up a part number for me? My jiffy stand was flopping around and I thought the spring was stretched so I picked up a new spring

    The dealer sugegsted the jiffy spring part number 50005-85A

    This spring appears to be the same as the one I am replacing. The old one is on the top, the new one on the bottom, see pic

    [​IMG]

    When I install this spring where does it connect? In reading posts here, some mention a hole in the frame that the spring clips into. On the sporty it seems to go around the bottom of the pin that the stand pivots on (top arrow in picture below), is that correct?

    The spring fell off tonight while riding so I couldn't verify where it came off of.

    Steve

    [​IMG]
     
    Last edited: Jun 5, 2009
  2. orgredneck

    orgredneck Member

    61
    16
    0
    Last edited: Jun 5, 2009
  3. NEWHD74FAN

    NEWHD74FAN Experienced Member Retired Moderators

    8,176
    98
    16
    The spring hooks in the groove of the frame anchor pin (it is near the removable round clevis pin w/ cotter pin), the other end goes in the hole of the jiffy stand leg. In my 2004 Service Manual Jiffy Stand info is under chassis pg 2-92 & 2-93.

    Below is the PDF of the 2005 Sportster...look at sm2c..."Jiffy Stand"

    2005 Sportster Service Manual Link 1

    2005 Sportster Service Manual Link 2 (in one ZIP archive)


    Of course you have to level the bike (I lean it against a wood fence or use wall hooks and Ancra straps to secure bike) first.

    To install the spring, you must remove the rubber stopper, which allows you to retract the jiffy stand even farther so spring can be installed easier with strong long nose pliers as the spring still needs a fair amount of tension after you hook the jiffy stand end first, to nudge it over the jiffy stand yoke retaining groove (make sure you wear eye protection).
     
  4. Steve_Benoit

    Steve_Benoit Member

    27
    11
    0
    Thanks folks, I'm going to install it shortly and will let you know how it goes

    Its strange that the 2 springs appear the same and the old one doesn't look stetched

    thanks a again

    Steve
     
  5. NEWHD74FAN

    NEWHD74FAN Experienced Member Retired Moderators

    8,176
    98
    16
    Thats because it is an "overcenter" type spring, in that it has modest tension when retracted or deployed and at maximim when you swing it to the middle of the arc.
     
  6. Steve_Benoit

    Steve_Benoit Member

    27
    11
    0
    I replaced the spring and it seems better but is still looser than I would have thought it should be. See the attache video clip, it has the new spring installed :

    http://www.benoits.ca/2007XL883L-jiffy-small.m4v

    I would have thought that the stand would come up and make contact with the rubber stopper on the frame. But as you can see in the video, in the retracted position I can still put my finger between the stand and the stopper.

    Is this normal ? Non of the folks I ride with have Sportsters so I can't compare there. Thi sall started with the stand drag in left hand coners and escalated to the spring falling off yesterday.

    With the new spring, the stand doesn't seem to drag in lefthand corners but is still loose.
     
  7. NEWHD74FAN

    NEWHD74FAN Experienced Member Retired Moderators

    8,176
    98
    16
    Does not sound right, the spring should hold the jiffystand with modest pressure against the rubber stopper, otherwise going over bumps would cause it to bang around. Might need a shorter spring...or something is bent or amiss?
     
  8. Steve_Benoit

    Steve_Benoit Member

    27
    11
    0
    I didn't think it sounded right either.

    As for the shorter spring, I went to the dealer and purchased a new spring for a sportser and they sold me the part "50005-85A Jiffystand soring, softtails"

    I'm going to try and confirm the part is proper for the 883L and continue to look for something bent

    thanks for the help
     
  9. glider

    glider Veteran Member

    25,464
    108
    44
    PN 50005-85A fits the following models, can't find it listed for an 07 but they could be older listings too.

    1985 - 2006 Softail®

    1986 - 1990 Heritage Softail®

    1986 - 1998 Softail® Custom

    1987 - 2006 Heritage Softail® Classic

    1988 - 2006 Springer Softail®

    1990 - 2003 XLH1200

    1990 - 2005 883 Hugger®

    1990 - 2006 Fat Boy®

    1991 - 1992 FXR Touring

    1991 - 1993 Low Rider® Convertible

    1991 - 1993 Low Rider® Sport Edition

    1991 - 1994 FXR Police

    1991 - 1994 Low Rider/Special Edition

    1991 - 1994 Rubber Mount Super Glide

    1991 Low Rider®

    1993 - 2004 Nostalgia®

    1995 - 1997 Bad Boy®

    1996 - 2003 XLH1200S

    1996 - 2005 XLH1200C

    1997 - 2003 Heritage Springer Softail®

    1999 - 2005 XLH883C

    1999 - 2006 Night Train®

    1999 FXR CVO (1st Edition)

    1999 FXR CVO (2nd Edition)

    2000 - 2006 Softail® Deuce™

    2000 FXR CVO (3rd Edition)

    2001 - 2003 Softail® Deluxe

    2001 - 2006 Fat Boy® EFI

    2001 - 2006 Heritage Softail® Classic EFI

    2001 - 2006 Night Train® EFI

    2001 - 2006 Softail® Deuce™ EFI

    2001 - 2006 Softail® EFI

    2001 - 2006 Springer Softail® EFI

    2002 - 2003 XLH883R

    2004 - 2005 XLH1200R

    2004 Screamin Eagle® Deuce™

    2005 - 2006 Nostalgia® EFI

    2005 - 2006 Softail® Deluxe

    2005 - 2006 Softail® Deluxe EFI

    2005 883 Low®

    2005 Screamin Eagle® Fat Boy®

    2006 FLSTI

    2006 Heritage Softail®

    2006 Nostalgia®

    2006 XL 1200

    2006 XL 1200C

    2006 XL 1200R

    2006 XL 883

    2006 XL 883C

    2006 XL 883L

    2006 XL 883R
     
  10. Steve_Benoit

    Steve_Benoit Member

    27
    11
    0
    Thanks Glider - I'm going to look for a 2007 parts catalog and confirm the part number.