Manual Alarm Disarming Procedure

If you should loose your button less smart alarm fob, here the procedure to deactivate the alarm system so the engine can be started using the directional switches.

Code = A * B * C * D * E (Five digit PIN codes)

How to check/set this code is covered here.
http://www.hdtalking.com/diagnostics_alarms_security_and_fuel_injection_rel ated/1326-programming_using_manual_security_code.html

1. If necessary verify the correct 5 digit PIN

2. Turn ignition key to IGNITION

3. Quickly within 2 seconds of turning key hold both turn signal switches in until confirmation.
> Key icon flashes at a fast rate In the odometer window a flashing dash will be followed by four more dashes.

4. Enter first digit (A) in the PIN by pressing left turn switch A times.
> The first digit (A) in the odometer will be the first digit in the PIN.

5. Press RIGHT turn switch 1 time. (Serves as enter key)
> The first digit is stored and the dash will flash.

6. Enter the second digit (B) in the pin number by pressing LEFT turn switch B times.
> The second digit (B) in the odometer will be the second digit in the PIN.

7. Press RIGHT turn switch one time. (Serves as enter key)
> The second digit is stored and the next dash will flash.

8. Enter the third digit (C) in the PIN by pressing LEFT turn switch C times.
> The third digit (C) will be the third digit in the PIN.

9. Press RIGHT turn switch one time. (Serves as enter key)
> The third digit is stored and the next dash will flash.

10. Enter the fourth digit (D) in the PIN by pressing LEFT turn switch D times.
> The fourth digit (D)in the odometer will be the fourth digit in the PIN.

11. Press RIGHT turn switch 1 time. (Serves as enter key)
> The fourth digit (D) is stored and the next dash will flash.

12. Enter the fifth digit (E) in the PIN by pressing LEFT turn switch E times.
> The fifth digit (E) in the odometer will be the fifth digit in the PIN.

13. Press RIGHT turn switch 1 time. (Serves as enter key)
> The fifth digit is stored. The icon stops blinking and the alarm is over ridden. You can now start the motor.

Chopp · Nov 19th, 2009, 09:56 PM

Hello, I just bought a wrecked 07 Road King without any key fob. It appears to have the security system and it is preventing the engine from being started. I do not know the PIN number and like I said, I don't have the key fob. Is there a generic code that can be entered if the previous owner didn't change it? Any other way of bypassing the system? Thanks for the help.

glider · Nov 19th, 2009, 09:58 PM

If you go to the local HD dealer with the papers to prove ownership and the VIN number, he may be able to locate the original selling dealer and they may be able to give you their setup PIN number providing the previous owner didn't change it. Otherwise you have to replace the TSSM or the TSM can be installed which wouldn't give you an alarm but would be a bit cheaper.

You didn't say if you had a FOB.

Have you tried to extract the PIN number using the procedure above?

Nov 19th, 2009, 09:56 PM	#1
Chopp New Family Ride: 2006 Road King Join Date: Nov 19th, 2009 Posts: 1	Re: Manual Alarm Disarming Procedure Hello, I just bought a wrecked 07 Road King without any key fob. It appears to have the security system and it is preventing the engine from being started. I do not know the PIN number and like I said, I don't have the key fob. Is there a generic code that can be entered if the previous owner didn't change it? Any other way of bypassing the system? Thanks for the help.

Nov 19th, 2009, 09:58 PM	#2
glider Community Liaison Ride: 07 Road King Classic Join Date: Jun 21st, 2007 Posts: 21,062 My Mood:	Re: Manual Alarm Disarming Procedure If you go to the local HD dealer with the papers to prove ownership and the VIN number, he may be able to locate the original selling dealer and they may be able to give you their setup PIN number providing the previous owner didn't change it. Otherwise you have to replace the TSSM or the TSM can be installed which wouldn't give you an alarm but would be a bit cheaper. You didn't say if you had a FOB. Have you tried to extract the PIN number using the procedure above?

Tip Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Manual Alarm Disarming Procedure

Alarms and Security Related Issues